#DEFAULT MAC WIFI SETTINGS HOW TO#
#DEFAULT MAC WIFI SETTINGS PC#
#DEFAULT MAC WIFI SETTINGS PLUS#

Go to Advanced > Net & Wifi Click on the 'reset to default network settings' button.Modern Mac users have multiple ways to connect to a network or the Internet, including Wi-Fi and Ethernet. Now you can unplug the Vera unit from your computer and connect it to the internet. This will reset the unit to default network settings and can take up to 5 minutes. Now you can unplug the Vera unit from your computer and connect it to the internet.Д¬lick on the 'reset to default network settings' button. Go to Settings > Net & Wi-fi Click on the вЂњReset to default network settingsвЂќ button.Д¬onfirm by clicking the вЂњOKвЂќ Button on the pop-up window. Now you can see the DASHBOARD page of your Vera unit.

Now open an web browser and type this in the address bar: 192.168.81.1 Plug a network cable from your computer into Vera's LAN port Select 'Manually' from the Configure IPv4 dropdownД®nter 192.168.81.10 in the IP address fieldД®nter 255.255.255.0 in the subnet mask field Select 'Ethernet' from the list on the left

#DEFAULT MAC WIFI SETTINGS PLUS#

Open the Apple Menu(Top left corner of your screen)Д¬lick the Locations dropdown and select Edit LocationsД¬lick the plus sign and call your new location 'Vera system Troubleshooting' In the General tab, highlight the Internet Protocol (TCP/IP) item, and click Properties. In the Default gateway field enter 192.168.81.1Д¬ategory view: Select Network and Internet Connections, and then Network Connections.Дouble-click on your the LAN connection to Vera. In the subnet mask field enter 255.255.255.0 In the IP address field enter 192.168.81.10

Highlight the Internet Protocol Version 4 (TCP/IPv4) item, and click on Properties Right click on LAN connection to Vera, then click on Properties View by: Category -> View netork status and tasks View by: Large icons -> Network and Sharing Center Right click on the 'Ethernet' connection and click on 'Properties'ДЇrom the list highlight 'Internet Protocol Version 4 (TCP/IPv4) and click on the 'Properties' buttonД¬heck 'Use the following IP address:' and fill in the three fields as follows: or 192.168.23.100 (for example) for case b.ДЇrom the Tiles menu click on 'PC Settings'ДЇrom the bottom left of the menu select 'Control Panel'Д¬lick on 'Network and Internet' and then select 'Network and Sharing Center'Д¬lick on 'Change adapter settings' in the left menu

#DEFAULT MAC WIFI SETTINGS PC#

This would mean that the PC should have an IP address in the same class as the unit, meaning 192.168.12.100 (for example) for case a. For the example above it would be 192.168.23.94 on firmware version newer than 7.0.12.1 (above ) the IP address Vera Edge can be accessed on will be generated using the last 4 characters of the mac address, where the letters are converted to numbers based on their order of the alphabet. For the example above it would be: 192.168.12.29Д«. on firmware version 7.0.12.1 and older ( or older) the IP address Vera Edge can be accessed on will be generated using the last 4 digits in the mac address. Depending on which firmware version you're on you'll have to set it up like below:ДЄ. Note: For Vera edge you'll have to replace the 192.168.81.1 IP address with a combination of numbers based on the unit's MAC address. If after plugging Vera into your network, you don't see your Vera on cp., please follow these steps to fix your networking:

#DEFAULT MAC WIFI SETTINGS HOW TO#

How to reset to default network settings on your Vera ControllerД«y default Vera automatically configures its network, if you connect it to your router it will automatically connect to it's network.

Default mac wifi settings